Case 2050M Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 286

Case 2050M Скачать руководство пользователя страница 11

1 - GENERAL INFORMATION

Product identification

Model, Product Identification Number (PIN), and year of manufacture

Record the machine Product Identification Number (PIN) and additional machine information including the model and
the component serial numbers in the spaces below. Always supply this information to your dealer when you order
parts, obtain information, or require assistance. Keep a record of these numbers and your Manufacturer’s Statement
of Origin in a safe place. If the machine is stolen, report the numbers to your local law enforcement agency.

Machine identification

Model name

Product Identification Number (PIN)

Model year

The PIN plate is located on the left-hand side of the ma-
chine in front of the engine access door.

RAPH12DOZ0131AA

1

Roll-Over Protective Structure (ROPS)

The ROPS serial number plate is located in the left-hand
rear access compartment.

RAIL15DOZ0015AA

2

Engine make and model

Engine serial number

The serial number plate is on the engine valve cover.

RAIL13DOZ1693AA

3

1-5

«
...
9
10
11
12
13
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов