Case 2050M Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 286

Case 2050M Скачать руководство пользователя страница 8

1 - GENERAL INFORMATION

Store this operator's manual in the manual compartment equipped on this machine. Make sure this manual is com-
plete and in good condition. Contact your dealer to obtain additional manuals or manuals in languages other than
that of the country of use.

Your CASE CONSTRUCTION dealer is available for any further information. They will also provide any after-sales
service you may need, to include genuine CASE CONSTRUCTION spare parts, your guarantee of quality and match.
CASE CONSTRUCTION customer assistance is also available. Go to www.casece.com.

This is the safety alert symbol. It is used with and without signal words to alert you to potential
personal injury hazards. Obey all safety messages that follow this symbol to avoid possible
death or injury.

WARNING

Illustrations in this manual may show protective shielding open or removed to better illustrate a par-
ticular feature or adjustment.
Replace all shields before operating the machine.
Failure to comply could result in death or serious injury.

W0012A

Improvements

CNH Industrial America LLC is continually striving to improve its products. We reserve the right to make improvements
or changes when it becomes practical and possible to do so, without incurring any obligation to make changes or
additions to the equipment sold previously.

1-2

«
...
6
7
8
9
10
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов