Case 2050M Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 286

Case 2050M Скачать руководство пользователя страница 67

3 - CONTROLS AND INSTRUMENTS

Fuel level gauge

The fuel level gauge

(4)

indicates the fuel

level. Normal operating range is in the
green zone. When the tank is almost empty
the gauge will move into the yellow zone
and the fuel indicator will turn on and the
warning alarm will sound for a few seconds.

NOTICE:

Do not allow the machine to run completely out

of fuel.

RAIL12DOZ0821AA

7

Fuel level gauge

Gauge indication

Condition

Master indicator

Gauge status

Alarm status

8 %

and below

Fuel level low

Caution (yellow)

ON

3 Seconds

14 %

and above

Fuel level normal

NOTICE:

Do not operate the machine if the indicator turns red and the alarm sounds continuously. Stop the machine

and correct the problem.

3-19

«
...
65
66
67
68
69
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов