Case 2050M Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 286

Case 2050M Скачать руководство пользователя страница 7

1 - GENERAL INFORMATION

1 - GENERAL INFORMATION

###_1_###

Note to the owner

RAIL12DOZ0388FA

1

Read this manual before you start the engine or operate the machine. This manual contains important information
about the safe operation and maintenance of your machine. Refer to the index at the back of this manual for locating
specific items about your machine. This crawler dozer conforms to current safety regulations.

Consult an authorized dealer or CNH Industrial America LLC on changes, additions, or modifications that can be
required for this machine to comply with various country regulations and safety requirements. Unauthorized modi-
fications will cause serious injury or death. Anyone making such unauthorized modifications is responsible for the
consequences.

The information in this manual is provided on the basis of information that was available at the time the manual was
written. Settings, procedures, part numbers, software, and other items can change. These changes can affect the
maintenance performed on the machine. Ensure that you have complete and current information from your dealer
before you start any machine operation.

ATTENTION:

The engine and fuel system on your machine is designed and built to government emission standards.

Tampering by dealer, customers, operators, and end users is strictly prohibited by law. Failure to comply could result
in government fines, rework charges, invalid warranty, legal action, and possible confiscation of the machine until
rework to original condition is completed. Engine service and/or repairs must be done by a certified technician only!

Before you permit a new operator to operate the machine, make sure that:

• The operator reads and understands the instructions in this operator's manual

• The operator understands ALL safety signs on the machine

All persons who will be operating this machine shall possess a valid local vehicle operating permit and/or other appli-
cable local age work permits.

1-1

«
...
5
6
7
8
9
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов