manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 220 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 220

7 - MAINTENANCE

Every 1000 hours

Fuel tank sediment

WARNING

Hot liquid under pressure!
Fuel in the high pressure fuel line is still under pressure immediately after you shut down the engine.
Before performing any maintenance or inspection, wait for 2 minutes after engine shutdown to allow
the pressure to drop.
Failure to comply could result in death or serious injury.

W0249A

WARNING

Chemical hazard!
When handling fuel, lubricants, and other service chemicals, follow the manufacturer's instructions.
Wear Personal Protective Equipment (PPE) as instructed. Do not smoke or use open flame. Collect
fluids in proper containers. Obey all local and environmental regulations when disposing of chemi-
cals.
Failure to comply could result in death or serious injury.

W0371A

Drain condensation from the fuel tank when the hour meter registers 1000 hours of operation and every 1000 hours
thereafter. Drain more frequently if conditions so require. The fuel tank drain is located on the left side of the machine.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

1. On machines with the environmental drain option, a fuel

tank drain hose is supplied and located behind a bolt-on
panel on the left side of the machine. Have a suitable
container ready to collect the condensation and fuel.
Dispose of the waste following local regulations.

RAPH12DOZ0042AA

1

NOTE:

On machines that are not equipped with the environmental drain option, connect a drain hose to the fuel tank

drain valve. The drain valve is accessible through the right rear access panel or by removing the cab floor access
panel and tilting back the operator’s seat.

7-64

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов