Case 2050M Скачать руководство пользователя страница 213

Страница: 213 / 286

7 - MAINTENANCE

3. Remove the final drive fill/check plug

(1)

slowly.

RAIL13DOZ1269AA

4. Have a suitable container ready, and slowly remove the

final drive drain plug

(2)

RAPH12DOZ0384AA

5. Remove the planetary fill/check plug

(3)

slowly.

6. Have a suitable container available. Slowly remove the

planetary drain plug

(4)

, and allow all oil to drain into a

suitable container.

RAPH12DOZ0383AA

7. Replace final drive and planetary drain plugs after oil

has completely drained

8. Fill with new oil through the fill/check plug

(1)

and

(3)

according to specifications. The oil will just begin to run
from the fill/check plugs.

9. Install the fill/check plugs, and repeat the procedure for

the other side.

10. Check for leaks.

7-57

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 213 / 286

Результаты поиска

Содержание 2050M

Отзывы: