manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 121 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 121

4 - OPERATING INSTRUCTIONS

Hydrostatic drive speed controls

WARNING

Hazard to bystanders!
Always sound the horn before starting the machine. Make sure the work area is clear of other persons,
domestic animals, tools, etc. before you operate the machine. Never allow anyone in the work area
during machine operation.
Failure to comply could result in death or serious injury.

W0304A

The crawler has variable speed selections in either for-
ward and reverse. Select a maximum speed in a range
of 15 increments. Press the UP

(1)

or DOWN

(2)

button

to move from one speed to another. This allows the op-
erator to increase speed one increment at a time by each
touch of the button. Move continuously through the drive
speeds by holding the button in.

NOTE:

The speed can only be increased to the maximum

drive speed setting. The maximum drive speed setting
can be adjusted. The highest speed from the factory is
preset at 15.

NOTE:

The transmission speed will default to 8 when the

crawler engine is turned off.

NOTE:

The horn button is also located on the joystick.

Always sound the horn before starting the machine.

RAPH12DOZ0079AA

1

1. Hydrostatic drive increase speed (Hare)
2. Hydrostatic drive decrease speed (Tortoise)

The drive speed on the multi-function display shows
the speed selected. When the crawler engine is initially
turned on, the drive speed will default to 8.

The multi-function display also shows the position of the
direction control lever as Forward (F), Neutral (N), or Re-
verse (R). If the F or R flashes, the directional control lever
must be returned to neutral before the crawler will move.

NOTE:

The crawler will not move unless the engine speed

is above approximately

1200 RPM

.

RAIL12DOZ0224AA

2

4-19

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов