Case 2050M Скачать руководство пользователя страница 184

Страница: 184 / 286

7 - MAINTENANCE

After Starting the Engine

Do the following:

• Did the engine start correctly? Are the exhaust fumes normal? Any unusual noises?

• Check for abnormal noise on the hydraulic components.

• Check for water, fuel, or oil leaks on the components.

• Check the audible alarm devices, working lights and windshield wipers.

• Check that all hydraulic circuits are functioning correctly.

Access doors and fill locations

1. Access door - rear right-hand side of the machine.

Hydraulic sight gauge

(1)

Hydraulic Test ports

(2)

Hydraulic filters

(3)

Windshield wiper reservoir

(4)

Fuel filter

(5)

RAIL13DOZ1686AA

2. Engine hood - front right-hand side of the machine.

Oil filter

RAIL13DOZ1688AA

3. Access door - rear left-hand side of the machine.

Batteries

(1)

Fuses

(2)

Electronic disconnect

(3)

RAPH12DOZ0043AA

7-28

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 184 / 286

Результаты поиска

Содержание 2050M

Отзывы: