Case 2050M Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 286

Case 2050M Скачать руководство пользователя страница 13

1 - GENERAL INFORMATION

Operator's manual storage

The operator’s manual storage compartment is located on
the operator’s seat back.

READ THIS MANUAL COMPLETELY and make certain
you understand the controls. All equipment has a limit.
Make sure you understand the speed, steering, stability,
and load characteristics of this machine before you start
to operate.

DO NOT remove this manual from the machine. See your
dealer for additional manuals. Always keep the operator's
manual in the storage compartment provided on the ma-
chine. The operator's manual must be available for use
by all operators.

When you see this symbol read your
operator's manual.

When you see this symbol refer to your
service manual.

RAIL12DOZ0547AA

1

1-7

«
...
11
12
13
14
15
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов