Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 92 | Manualshive

Page: 92 / 768

Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 92

5.4.2

Connecting the motor

NOTICE
Destruction of the motor if it is directly connected to the three-phase line supply
The motor will be destroyed if it is directly connected to the three-phase line supply.
● Only operate motors with the permitted converters.

The manufacturer of the system/machine is responsible for ensuring that installation is

performed correctly.
Ensure that the associated warning labels in the appropriate national language are attached.
The motors are equipped with a rotatable cable outlet with SPEED-CONNECT connectors

M12 or M17.
The motor is connected to the converter with a MOTION-CONNECT OCC cable. The cables

for the power, the holding brake, the encoder and the shielding are integrated in the OCC cable.
● Use the prefabricated MOTION-CONNECT OCC cables from SIEMENS.

8
:

9

%

$

①

Round connector M12 or M17, 10-pin

④

Cables for holding brake

②

MOTION-CONNECT OCC cable

⑤

Power cables

③

Shielding

⑥

SIEMENS IX connector for signal line

Figure 5-5

MOTION-CONNECT OCC

The cables have a SPEED-CONNECT connector. This reduces the installation time and

costs, and increases the operational reliability of the drive.

● Check that the sealing surfaces of the connectors have not been damaged.

Clearance required when connecting the motor

O

O

5

Figure 5-6

Clearances for OCC connection at the motor

Installing
5.4 Connecting the converter and the motor

SINAMICS S210 servo drive system

90

Operating Instructions, 12/2017, A5E41702836B AA

«
...
90
91
92
93
94
...
»

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands