manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 477

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

- the motor parameters were incorrectly entered while commissioning (e.g. p0300 = 0, no motor)
- the braking resistor has still not been parameterized - commissioning cannot be completed.
Fault value (r0949, interpret decimal):
Parameter number involved.
300 (CU250S-2):
For this control mode, the motor type is not supported.
307:
The following motor parameters could be incorrect:
p0304, p0305, p0307, p0308, p0309
See also: p0304, r0304, p0305, r0305, p0307, r0307, p0311, r0311, p0322, r0322, p0323, r0323

Remedy:

Compare the motor data with the rating plate data and if required, correct.
For fault value = 300 (CU250S-2):
Operate a motor type supported by the selected control mode.

Reaction upon A: NONE
Acknowl. upon A: NONE

F07955

Drive: Motor has been changed

Message value:

Parameter: %1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

The code number of the actual motor with DRIVE-CLiQ does not match the saved number.
Fault value (r0949, interpret decimal):
Number of the incorrect parameter.
See also: r0302

Remedy:

Connect the original motor, switch on the Control Unit again (POWER ON) and exit quick commissioning with p0010 = 0.
Or set p0300 = 10000 (load the parameters from the motor with DRIVE-CLiQ) and re-commission.
Quick commissioning (p0010 = 1) is automatically exited with p3900 > 0.
If quick commissioning was exited with p0010 = 0, then an automatic controller calculation (p0340 = 1) is not carried out.

F07956 (A)

Drive: Motor code does not match the list (catalog) motor

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

The motor code of the connected motor with DRIVE-CLiQ does not match the possible list motor types (see selection in 

p0300).
The connected motor with DRIVE-CLiQ might not be supported by this firmware version.
Fault value (r0949, interpret decimal):
Motor code of the connected motor with DRIVE-CLiQ.
Note:
The first three digits of the motor code generally correspond to the list motor type.

Remedy:

Use a motor with DRIVE-CLiQ and the matching motor code.

Reaction upon A: NONE
Acknowl. upon A: NONE

A07960

Drive: Incorrect friction characteristic

Message value:

Parameter: %1

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

475

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands