manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 428

Remedy:

- check the motor load and if required, reduce.
- check the motor ambient temperature.
- check activation of the motor temperature model (p0612).
Motor temperature model 1 (I2t):
- check the thermal time constant (p0611).
- check alarm threshold.
Motor temperature model 3:
- check the motor type.
- check alarm threshold.
- check the model parameters.
See also: r0034

Reaction upon N: NONE
Acknowl. upon N: NONE

F07013

Drive: Motor temperature model configuration fault

Message value:

%1

Drive object:

All objects

Reaction:

OFF2 (NONE, OFF1, OFF3, STOP2)

Acknowledge:

IMMEDIATELY

Cause:

A fault has occurred in the configuration of the motor temperature model.
Fault value (r0949, interpret decimal):
300:
Motor temperature model 3: The sensor does not supply the necessary sensor temperature for the thermal model.
301:
Motor temperature model 3: The sensor type is unknown.
302:
Motor temperature model 3: At least one other temperature model was simultaneously activated.
303:
Motor temperature model unknown in the actual firmware version.

Remedy:

- check the encoder type.
- check the motor type.
- check activation of the motor temperature model (p0612).
- check the parameters of the motor temperature model (p5350 and following).

A07014 (N)

Drive: Motor temperature model configuration alarm

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

A fault has occurred in the configuration of the motor temperature model.
Alarm value (r2124, interpret decimal):
1:
All motor temperature models: It is not possible to save the model temperature
300:
Motor temperature model 3: Threshold value for alarm (r5398) is higher than the threshold value for fault (r5399).

Remedy:

- set the response for motor overtemperature to "Alarm and fault, no reduction of I_max" (p0610 = 2).
- check and correct the threshold values (r5398, r5399).

Reaction upon N: NONE
Acknowl. upon N: NONE

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

426

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands