Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 231

Page: 231 / 768

Device configuration

30:

Parameter reset

Note
The drive can only be switched on when in the "Ready" state (p0009 = 0).

p0010

Drive commissioning parameter filter 2

Changeable: C2(1), T

Data type: Integer16

P group: All groups

Min: 0

Max: 95

Def: 1

Description:

Setting parameter filter 2 for commissioning the drive.

Value:

Ready

Only Siemens internal

Motor commissioning

95:

Safety Integrated commissioning

NOTICE
For p0010 = 95:
The safety commissioning Wizard must be carried out in the web server after changing safety parameters. These

changes become effective after carry out all of the commissioning steps of the wizards.

Note
The drive can only be switched on when in the "Ready" state (p0010 = 0).

r0020

Speed setpoint smoothed

Data type: FloatingPoint32

P group: Displays, signals

Scaling: p2000

Description:

Displays the smoothed speed setpoint at the speed controller input.

r0021

Actual speed smoothed

Data type: FloatingPoint32

P group: Displays, signals

Scaling: p2000

Description:

Displays the smoothed actual value of the motor speed.

Dependency:

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands