manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 101

Connect the shield of the motor connection cable to the shield plate over a large area. Use 

commercially available clamps, the clamps supplied with the prefabricated cable or the shield 

connection clamps supplied as accessories.

Connecting the encoder to the converter

The cables and the connector for the encoder connection are part of the prefabricated 

MOTION-CONNECT cable from the motor to the converter.

NOTICE
Damage to the device by connecting other motors or devices
Connecting other devices (motors, encoders) can destroy the converter or the connected 

device. 
● Only connect 1FK2 motors to this interface.
● Use only MOTION-CONNECT OCC cables from Siemens - or cables that you have 

fabricated yourself with the correct pin assignment.

To connect the encoder, insert the Siemens IX connector as shown in the following in the X100 

plug socket.

Figure 5-14

X100 - encoder connection

Connecting the motor holding brake

The cables for the motor holding brake are part of the prefabricated MOTION-CONNECT cable 

from the motor to the converter.
Connect the cables as shown below to the connector X107 of the converter.

%5

%5

Figure 5-15

X107 - connecting the motor holding brake

The terminals are spring-loaded terminals.
Permissible conductor cross-sections:
● For single-conductor cables or for flexible cables with end sleeves without plastic protection: 

0.25 mm

2

 … 1.5 mm

2

, AWG: 24 … 16

● For flexible cables with end sleeves with plastic protection: 

0.25 mm

2

 … 0.75 mm

2

, AWG: 24 … 19

Installing

5.4 Connecting the converter and the motor

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

99

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands