manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 260

Note
The higher the dynamic factor, the faster and more unstable the control.

r5293

FFT tuning speed controller P gain identified

 

Data type: FloatingPoint32

P group: Closed-loop control

 

Description:

Displays the determined proportional gain Kp of the speed controller before FFT tuning.
This function is used for One Button Tuning (p5300 = 1).

Dependency:

See also:  p5291

p5296[0...2]

Controller optimization noise amplitude

 

Changeable: T, U

Data type: FloatingPoint32

P group: -

Min: 1.0 [%]

Max: 300.0 [%]

Def: [0] 10.0 [%] [1] 30.0 [%] [2] 5.0 [%] 

Description:

The drive determines the noise amplitude for One Button Tuning and writes the value to p5296.

Dependency:

See also:  p5291

p5300[0]

One Button Tuning selection

 

Changeable: T

Data type: Integer16

P group: -

Min: -1

Max: 1

Def: 0 

Description:

Setting to activate/de-activate the One Button Tuning function.
If p5300 = 1:
The One Button Tuning function is configured using p5271 and p5301.

Value:

-1:

Reset controller parameters

 

0:

Inactive

 

1:

One Button Tuning

Dependency:

The motor must have already been commissioned so that One Button Tuning functions perfectly.
The One Button Tuning function is configured using p5271 and p5301.
The required dynamic performance of the control loop is set in p5292.
The traversing path for the test signal is parameterized in p5308.
Additional relevant parameters
p5309, p5296, p5297, r5274
See also:  p5271, r5274, p5292, r5293, p5296, p5301, p5308, p5309

Note
If p5300 = -1:
One Button Tuning is deactivated and p5300 is automatically set = 0. Further, the presetting values for the speed 

controller are restored.
If p5300 = 0:
To permanently save the values for the speed controller that have been determined, the parameters must be saved 

in a non-volatile memory.
If p5300 = 1:
One Button Tuning is active.
The moment of inertia is determined once using a test signal. The controller parameters and current setpoint filters 

are additionally determined once using a noise signal as excitation source. The steps to be executed can be configured 

using p5301.

p5301[0]

One Button Tuning configuration 2

 

Changeable: T, U

Data type: Unsigned32

P group: -

Min: -

Max: -

Def: 0000 0000 0000 0111 bin 

Description:

Setting the functions for One Button Tuning (p5300 = 1).
A test signal is required for some functions. Here, parameters p5307 to p5309 must be a taken into consideration.

Bit field:

Bit

Signal name

1 signal

0 signal

FP

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

258

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands