manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 702

Remedy:

- carry out a POWER ON.
- when a component is replaced, the same component type and if possible the same firmware version should be used.
- when a cable is replaced, only cables whose length is the same as or as close as possible to the length of the original 

cables should be used (ensure compliance with the maximum cable length).

F34950

VSM: Internal software error

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

An internal software error in the Voltage Sensing Module (VSM) has occurred.
Fault value (r0949, interpret decimal):
Information about the fault source.
Only for internal Siemens troubleshooting.

Remedy:

- if necessary, upgrade the firmware in the Voltage Sensing Module to a later version.
- contact Technical Support.

F35005

TM54F:parallel connection not supported

Message value:

Fault cause: %1 bin

Drive object:

All objects

Reaction:

NONE

Acknowledge:

POWER ON

Cause:

The TM54F function with Basic Safety Functions is used. This function is not supported when power units are connected 

in parallel.
All drives of the TM54F assume fail safe values, and are not enabled.

Remedy:

- deactivate parallel connection or TM54F with Basic Safety Functions.
- copy RAM to ROM.
- carry out a POWER ON (switch-off/switch-on).

F35851

TM DRIVE-CLiQ (CU): Sign-of-life missing

Message value:

Component number: %1, fault cause: %2

Drive object:

All objects

Reaction:

OFF1 (OFF2)

Acknowledge:

IMMEDIATELY

Cause:

A DRIVE-CLiQ communication error has occurred from the Terminal Module involved (TM) to the Control Unit.
The DRIVE-CLiQ component did not set the sign-of-life to the Control Unit.
Fault cause:
10 (= 0A hex):
The sign-of-life bit in the receive telegram is not set.
Note regarding the message value:
The individual information is coded as follows in the message value (r0949/r2124):
0000yyxx hex: yy = component number, xx = error cause

Remedy:

Upgrade the firmware of the component involved.

F35860

TM DRIVE-CLiQ (CU): Telegram error

Message value:

Component number: %1, fault cause: %2

Drive object:

All objects

Reaction:

OFF1 (OFF2)

Acknowledge:

IMMEDIATELY

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

700

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands