manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 305

Remedy:

- check the file attribute of the files (PSxxxyyy.***, CAxxxyyy.***, CCxxxyyy.***) and, if required, change from "read only" 

to "writeable".
- check the free memory space in the non-volatile memory. Approx. 80 kbyte of free memory space is required for every 

drive object in the system.
- replace the memory card or Control Unit.

Reaction upon A: NONE
Acknowl. upon A: NONE

F01040

Save parameter settings and carry out a POWER ON

Message value:

-

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

A parameter was changed in the drive system which means that it is necessary to save the parameters and re-boot.

Remedy:

- save parameters (p0971, p0977).
- carry out a POWER ON (switch-off/switch-on) for all components.
Then:
- upload the drive unit (commissioning tool).

F01041

Parameter save necessary

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

Defective or missing files were detected on the memory card when booting.
Fault value (r0949, interpret decimal):
1: Source file cannot be opened.
2: Source file cannot be read.
3: Target directory cannot be set up.
4. Target file cannot be set up/opened.
5. Target file cannot be written to.
Additional values:
Only for internal Siemens troubleshooting.

Remedy:

- save the parameters.
- download the project again to the drive unit.
- update the firmware
- if required, replace the Control Unit and/or memory card card.

F01042

Parameter error during project download

Message value:

Parameter: %1, Index: %2, fault cause: %3

Drive object:

All objects

Reaction:

Servo: OFF2 (NONE, OFF1, OFF3)

Acknowledge:

IMMEDIATELY

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

303

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands