manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 14

WARNING

Electric shock due to damaged motors or devices
Improper handling of motors or devices can damage them. 
Hazardous voltages can be present at the enclosure or at exposed components on damaged 

motors or devices. 
● Ensure compliance with the limit values specified in the technical data during transport, 

storage and operation. 

● Do not use any damaged motors or devices.

WARNING

Electric shock due to unconnected cable shields 
Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected 

cable shields.
● As a minimum, connect cable shields and the cores of cables that are not used at one end 

at the grounded housing potential.

WARNING

Electric shock if there is no ground connection 
For missing or incorrectly implemented protective conductor connection for devices with 

protection class I, high voltages can be present at open, exposed parts, which when touched, 

can result in death or severe injury.
● Ground the device in compliance with the applicable regulations.  

WARNING

Arcing when a plug connection is opened during operation
Opening a plug connection when a system is operation can result in arcing that may cause 

serious injury or death.
● Only open plug connections when the equipment is in a voltage-free state, unless it has 

been explicitly stated that they can be opened in operation.

WARNING

Electric shock due to residual charges in power components
Because of the capacitors, a hazardous voltage is present for up to 5 minutes after the power 

supply has been switched off. Contact with live parts can result in death or serious injury.
● Wait for 5 minutes before you check that the unit really is in a no-voltage condition and 

start work.

Fundamental safety instructions
1.1 General safety instructions

SINAMICS S210 servo drive system

12

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands