manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 377

Cause:

The forced checking procedure (test stop) for the safe motion monitoring functions is already selected when booting, which 

is not permissible.
This is the reason that the test is only carried out again after first selecting the forced checking procedure.
Note:
This message does not result in a safety stop response.

Remedy:

De-select the forced checking procedure for the safe motion monitoring functions and then select again.
Note:
The signal source to select the forced checking procedure is set via binector input p9705.
SI: Safety Integrated

Reaction upon F: NONE (OFF1, OFF2, OFF3)
Acknowl. upon F: IMMEDIATELY (POWER ON)

A01697 (F)

SI Motion: Test stop for motion monitoring functions required

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The time set in p9559 for the forced checking procedure (test stop) for the safe motion monitoring functions has been 

exceeded. A new forced checking procedure is required.
After the next time the forced checking procedure is selected, the message is withdrawn and the monitoring time is reset.
Note:
- this message does not result in a safety stop response.
- As the switch-off signal paths are not automatically checked during booting, an alarm is always issued once booting is 

complete.
- the test must be performed within a defined, maximum time interval (p9559, maximum of 9000 hours) in order to comply 

with the requirements as laid down in the standards for timely fault detection and the conditions to calculate the failure 

rates of safety functions (PFH value). Operation beyond this maximum time period is permissible if it can be ensured that 

the forced checking procedure is performed before persons enter the hazardous area and who are depending on the safety 

functions correctly functioning.
See also: p9559, r9765

Remedy:

Carry out the forced checking procedure of the safety motion monitoring functions.
The signal source to select the forced checking procedure is set via binector input p9705.
Note:
SI: Safety Integrated

Reaction upon F: NONE (OFF1, OFF2, OFF3)
Acknowl. upon F: IMMEDIATELY (POWER ON)

A01698 (F)

SI P1 (CU): Commissioning mode active

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The commissioning of the "Safety Integrated" function is selected.
This message is withdrawn after the safety functions have been commissioned.
Note:
- this message does not result in a safety stop response.
- in the safety commissioning mode, the "STO" function is internally selected.
See also: p0010

Remedy:

Not necessary.
Note:
CU: Control Unit
SI: Safety Integrated

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

375

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands