manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 206

8.3

Technical data and properties of the connection system

MOTION-CONNECT connection cables between the motor and the converter

The following technical data applies to the MOTION-CONNECT OCC cables.

Table 8-9

MOTION-CONNECT OCC cable with SPEED-CONNECT connector

Designation and use

Cable type

Connector 

size

Outer diame‐

ter

Minimum 

bending ra‐

dius, static

For con‐

nection to 

motor

Article number 

1)

D

max

 / mm

R

 / mm

Motor connection cable 

MC500 OCC for predom‐

inantly fixed installation

M12

9.7

23.5

1FK2☐02
1FK2☐03

6FX5002-8QN04-

☐☐☐☐

M17

10.5

25.5

1FK2☐04

6FX5002-8QN08-

☐☐☐☐

Motor connection cable 

MC800 OCC for use in a 

cable carrier

M12

9.7

28.2

1FK2☐02
1FK2☐03

6FX8002-8QN04-

☐☐☐☐

M17

10.5

30.6

1FK2☐04

6FX8002-8QN08-

☐☐☐☐

Extension cable 

MC500 OCC for predom‐

inantly fixed installation

M12

9.7

23.5

1FK2☐02
1FK2☐03

6FX5002-8QE04-

☐☐☐☐

M17

10.5

25.5

1FK2☐04

6FX5002-8QE08-

☐☐☐☐

Extension cable 

MC800 OCC for use in a 

cable carrier

M12

9.7

28.2

1FK2☐02
1FK2☐03

6FX8002-8QE04-

☐☐☐☐

M17

10.5

30.6

1FK2☐04

6FX8002-8QE08-

☐☐☐☐

1)

The last 4 positions (☐☐☐☐) define the cable length corresponding to the length code.

The length code can be found in Chapter:

Connection cables between the motor and the converter (Page 217)

Technical data and notes for cable carrier use with MC800 PLUS

Note
You require an MC800 PLUS cable to connect the motor using a cable carrier.

Technical specifications
8.3 Technical data and properties of the connection system

SINAMICS S210 servo drive system

204

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands