Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 151

Page: 151 / 768

6.8.2

Safety diagnostics

The most important information on the safety settings and the states of the converter are

displayed using the safety diagnostics.
Select "Safety" and "Safety Diagnostics" in the navigation.

Figure 6-29

Display of the safety functions

You receive the following individual information via separate display areas:
● "Diagnostics of the safety functions"

Shows which safety functions have been activated in the converter.

● "Status"

Information on the status of the converter. If a forced checking procedure is required, then

this is displayed. The times for the forced checking procedure of the timer and the remaining

time up to the forced checking procedure are displayed.

The display area also shows whether internal events (e.g. software errors in the converter

or a discrepancy in the monitoring channels) have taken place and whether the

communication is OK.

● "Checksums"

Uses the safety logbook to determine changes to safety parameters and to indicate if a

component has been replaced/exchanged. Shows changes in the form of functional

checksums with time stamps.

Commissioning and diagnostics in the Web server

6.8 Safety settings

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

149

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands