manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 188

The holding brakes of the 1FK2 have a torsional backlash of less than 1°. The following table 

contains additional technical data regarding the holding brakes:

Motor type

Holding 

torque

M

4

 at 

120 °C

Dyn. brak‐

ing torque 

M

1m

Opening 

time 

Closing 

time

Maximum 

permissi‐

ble single 

switching 

energy 

Maximum 

EMER‐

GENCY 

STOP 

speed

Total oper‐

ating ener‐

gy (serv‐

ice life)

M

4

 

/ Nm

M

1

 

/ Nm

t

 / ms

t

 / ms

W

 / J

n

 / rpm

W

max

 / kJ

1FK2☐02

0.32

0.2

50

15

7.4

8000

0.5

1FK2☐03

1.3

1.1

90

20

62

7500

5

1FK2☐04

3.3

3

110

30

268

7500

35

Holding torque M

4

The holding torque M

4

 is the highest permissible torque for the closed brake in steady-state 

operation without slip (holding function when motor is at standstill). The data applies for the 

state at operating temperature (120 °C).
Dynamic braking torque M

1m

The dynamic braking torque M

1m

 is the smallest mean dynamic braking torque that can occur 

for an EMERGENCY STOP. 
Opening time and closing time
The delay times that occur when switching the brake.
Maximum permissible single switching energy
The maximum permissible single switching energy of an individual EMERGENCY STOP 

procedure. 
After an EMERGENCY STOP with the maximum single switching energy, allow for a cooling 

time of at least 5 minutes before you put the motor into operation again.
Maximum EMERGENCY STOP speed
Maximum permitted speed for a safe EMERGENCY STOP procedure. 
Total operating energy (service life)
The total switching energy is the sum of the single switching energy (switching energy for each 

EMERGENCY STOP procedure). If the total switching energy is exceeded, flawless 

functioning of the brakes can no longer be guaranteed. 
● Refurbish the motor.

Formula for calculating the operating energy per braking operation
W 

BR

 = (

J 

Mot Br

 + 

J 

load 

) • 

n

mot

² / 182.4

W

 Br

 / J

Operating energy per braking operation

n

 Mot 

/ rpm

Speed at which the brake is engaged

Technical specifications
8.1 Technical data and properties of the motor

SINAMICS S210 servo drive system

186

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands