manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 404

Cause:

At this drive object, the connection to at least one Publisher for PROFIBUS peer-to-peer data transfer in cyclic operation 

has been aborted.
Fault value (r0949, interpret binary):
Bit 0 = 1: Publisher with address in r2077[0], connection aborted.
...
Bit 15 = 1: Publisher with address in r2077[15], connection aborted.

Remedy:

- check the PROFIBUS cables.
- check the state of the Publisher that has the aborted connection.

Reaction upon A: NONE
Acknowl. upon A: NONE

F01950 (N, A) PB/PN: clock cycle synchronous operation synchronization unsuccessful

Message value:

-

Drive object:

All objects

Reaction:

OFF1 (NONE)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

Synchronization of the internal clock cycle to the global control telegram has failed. The internal clock cycle exhibits an 

unexpected shift.

Remedy:

Only for internal Siemens troubleshooting.
Note:
PB: PROFIBUS
PN: PROFINET

Reaction upon N: NONE
Acknowl. upon N: NONE
Reaction upon A: NONE
Acknowl. upon A: NONE

F01951

CU SYNC: Synchronization application clock cycle missing

Message value:

%1

Drive object:

All objects

Reaction:

OFF2 (NONE)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

If DRIVE-CLiQ components with different application clock cycle are operated on a DRIVE-CLiQ port, this requires 

synchronization with the Control Unit. This synchronization routine was unsuccessful.
Fault value (r0949, interpret decimal):
Only for internal Siemens troubleshooting.

Remedy:

- carry out a POWER ON (switch-off/switch-on) for all components.
- upgrade the software of the DRIVE-CLiQ components.
- upgrade the Control Unit software.
Note:
If a Controller Extension is being used (e.g. CX32, NX10), then the following applies:
Check whether the Controller Extension is issuing error messages, and if required, remove these.

F01952

CU DRIVE-CLiQ: Synchronization of component not supported

Message value:

%1

Drive object:

All objects

Reaction:

OFF2 (NONE)

Acknowledge:

IMMEDIATELY (POWER ON)

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

402

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands