manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 290

r10241

SI Motion SBT load torque diagnostics

 

Data type: FloatingPoint32

P group: Safety Integrated

 

Description:

Displays the load torque for a safe brake test.
When initializing the brake test, this load torque is available at the drive.

Note
The value remains displayed until the brake test is deselected.

r10242

SI Motion SBT state diagnostics

 

Data type: Integer16

P group: Safety Integrated

 

Description:

Displays the actual state of the safe brake test.

Value:

0:

Brake test inactive, wait for SBT selection

 

1:

Setpoint input drive

 

2:

Determining the load

 

3:

Brake test is initialized, wait for start of test sequence

 

4:

Start test sequence

 

5:

Closing the brake, establishing the test torque

 

6:

Brake test active, wait for test duration sequence

 

7:

Reduce test torque

 

8:

Wait for the brake to open

 

9:

Brake test successfully completed, wait for start deselection

 

10:

Change to brake test initialized - fault acknowledgment

 

11:

Brake test canceled, torque is reduced

 

12:

Brake test canceled, wait for brake to open

 

13:

Brake test ended with error, wait for acknowledgment

 

14:

Brake opening timer elapsed

 

15:

Error when initializing the brake test, wait for acknowledgment

 

16:

Change to brake test inactive, acknowledgment active

r10251

SI Safety Control Channel control word S_STW1B diagnostics

 

Data type: Unsigned32

P group: -

 

Description:

Displays the diagnostics of control word S_STW1 of the safety control channel.

Bit field:

Bit

Signal name

1 signal

0 signal

FP

 

08

Extended functions test stop selection

Selected

Not selected

2837

 

12

Extended Functions premature SOS after STOP D

Selected

Not selected

-

Note
SCC: Safety Control Channel

p60000

PROFIdrive reference speed

 

Changeable: T

Data type: FloatingPoint32

P group: Communications

Min: 6.00 [rpm]

Max: 210000.00 [rpm]

Def: 3000.00 [rpm] 

Description:

Sets the reference quantity for the speed values.
All speeds specified as relative values refer to this reference quantity.
The reference quantity corresponds to 100% or 4000 hex (word) or 4000 0000 hex (double word).

Dependency:

See also:  p2000

Note
Parameter p60000 is an image of parameter p2000 in conformance with PROFIdrive.
A change always effects both parameters.

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

288

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands