manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 455

A07531

Drive: Command Data Set CDS not present

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The selected command data set is not available (p0836 > p0170). The command data set was not changed over.

Remedy:

- select the existing command data set.
- set up additional command data sets.

A07541

Drive: Data set changeover not possible

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The selected drive data set changeover and the assigned motor changeover are not possible and are not carried out.
For synchronous motors, the motor contactor may only be switched for actual speeds less than the speed at the start of 

field weakening (r0063 < p0348).
See also: r0063

Remedy:

Reduce the speed to below the speed at the start of field weakening (r0063 < p0348).

A07550 (F, N) Drive: Not possible to reset encoder parameters

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

When carrying out a factory setting (e.g. using p0970 = 1), it was not possible to reset the encoder parameters. The encoder 

parameters are directly read out of the encoder via DRIVE-CLiQ.
Alarm value (r2124, interpret decimal):
Component number of the encoder involved.

Remedy:

- repeat the operation.
- check the DRIVE-CLiQ connection.

Reaction upon F: Servo: NONE (IASC/DCBRK, OFF1, OFF2, OFF3, STOP2)
Acknowl. upon F: IMMEDIATELY (POWER ON)
Reaction upon N: NONE
Acknowl. upon N: NONE

F07551

Drive encoder: No commutation angle information

Message value:

Fault cause: %1, drive data set: %2

Drive object:

All objects

Reaction:

Servo: OFF2 (IASC/DCBRK)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The commutation angle information is missing. This means that synchronous motors cannot be controlled (closed-loop 

control)
Fault value (r0949, interpret decimal):
yyyyxxxx dec: yyyy = fault cause, xxxx = drive data set
yyyy = 1 dec:
The motor encoder used does not supply an absolute commutation angle.
yyyy = 2 dec:
The selected ratio of the measuring gear does not match the motor pole pair number.

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

453

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands