manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 468

Reaction upon A: NONE
Acknowl. upon A: NONE

F07890

Internal voltage protection / internal armature short-circuit with STO active

Message value:

-

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY

Cause:

The internal armature short-circuit (p1231 = 4) is not possible as Safe Torque Off (STO) is enabled. The pulses cannot be 

enabled.

Remedy:

Switch out the internal armature short-circuit (p1231=0) or deactivate Safe Torque Off (p9501 = p9561 = 0).
Note:
STO: Safe Torque Off / SH: Safe standstill

F07900 (N, A) Drive: Motor blocked/speed controller at its limit

Message value:

-

Drive object:

All objects

Reaction:

OFF2 (NONE, OFF1, OFF3, STOP2)

Acknowledge:

IMMEDIATELY

Cause:

Motor has been operating at the torque limit longer than the time specified in p2177 and below the speed threshold in 

p2175.
This signal can also be initiated if the speed actual value is oscillating and the speed controller output repeatedly goes to 

its limit.
See also: p2175

Remedy:

- check that the motor can freely move.
- check the effective torque limits (r1538, r1539).
- check the parameter, message "Motor blocked" and if required, correct (p2175, p2177).
- check the inversion of the actual value (p0410).
- check the motor encoder connection.
- check the encoder pulse number (p0408).
- for SERVO with encoderless operation and motors with low power ratings (< 300 W), increase the pulse frequency (p1800).
- after de-selecting the "Basic positioner" (EPOS) function mode, check the motoring (p1528) and regenerative (p1529) 

torque limit and modify again.
- blocksize device: for encoderless operation and a current controller sampling time p0115[0] < 80 µs, either set the pulse 

frequency of p1800 = 1 / p0115[0] or increase the switchover speed of the model p1755.

Reaction upon N: NONE
Acknowl. upon N: NONE
Reaction upon A: NONE
Acknowl. upon A: NONE

F07901

Drive: Motor overspeed

Message value:

-

Drive object:

All objects

Reaction:

Servo: OFF2 (IASC/DCBRK)

Acknowledge:

IMMEDIATELY

Cause:

The maximum permissible speed was either positively or negatively exceeded.
The maximum permissible positive speed is formed as follows: Minimum (p1082, CI: p1085) + p2162
The maximum permissible negative speed is formed as follows: Maximum (-p1082, CI: 1088) - p2162

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

466

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands