manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 103

5.4.3.3

Connections for open-loop and closed-loop control of the converter

Connecting service interface and PROFINET

Connect your commissioning device using an Ethernet cable to 

the service interface (socket X127).
The transmission rates are 10 Mbit/s or 100 Mbit/s.
Connect the converter with PROFINET cables with RJ45 FastConnect connectors or with 

PROFINET patch cables (see accessories) via the sockets X150 P1 and X150 P2 to the 

PROFINET network.

Table 5-3

Pin assignment for X127, X150 P1 and X150 P2

 

Pin

Pin assignment

Explanation

 
 
 

1

RXP

Receiving data +

2

RXN

Receiving data -

3

TXP

Sending data +

4

Reserved

 

5

Reserved

 

6

TXN

Sending data -

7

Reserved

 

8

Reserved

 

Connecting an external braking resistor

If you are using the internal braking resistor, DCP and R2 must be jumpered. 
If you are using an external braking resistor, DCP and R2 must not be jumpered. Connect the 

external braking resistor via the DCP and R1 terminals.

6KLHOG

'&3

5

5

'&3

5

5

①

Jumper when you use the internal braking resistor.
The jumper is included in the scope of delivery of the converter

②

Connect an external braking resistor
Protective conductor connection and shield support via the shield plate

Figure 5-16

X1 - connecting an external braking resistor

The terminals are spring-loaded terminals.
Permissible conductor cross-sections for single-core connection or for the connection of 

flexible cables with end sleeves: 

Installing

5.4 Connecting the converter and the motor

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

101

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands