manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 100

5.4.3.2

Connecting the line supply, motor, motor holding brake and encoder to the converter

Connecting the line supply to the converter

Connect the line supply as shown in the following to connector X1 of the converter. Connect 

the protective conductor with a cable lug and an M4 screw to the shield plate of the converter.
Information about stripping the insulation can be found in Chapter "Connection cables between 

the motor and the converter (Page 217)".
If you do not use a shield plate, then you must connect the protective conductor directly at the 

device.

1P

/

1

Figure 5-12

X1 - line connection

The terminals are spring-loaded terminals.
Permissible conductor cross-sections for single-core connection or for the connection of 

flexible cables with end sleeves: 

•  0.2 mm

2

 … 2.5 mm

2

•  AWG: 26 … 12

Connecting the motor to the converter

Connect the motor as shown in the following to connector X2 of the converter.
Color coding for MOTION-CONNECT OCC cables: Phase U = brown, phase = V black, phase 

W = gray

1P

Figure 5-13

X2 - motor connection

The terminals are spring-loaded terminals.
Permissible conductor cross-sections for single-core connection or for the connection of 

flexible cables with end sleeves: 

•  0.2 mm

2

 … 2.5 mm

2, 

•  AWG: 26 … 12

Installing
5.4 Connecting the converter and the motor

SINAMICS S210 servo drive system

98

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands