manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 424

Remedy:

Use power units with the same code number.
For parallel circuit configurations, only power units with identical power unit data may be used.

F05056

Parallel circuit: Power unit EEPROM versions differ

Message value:

Parameter: %1

Drive object:

All objects

Reaction:

OFF2 (NONE)

Acknowledge:

IMMEDIATELY

Cause:

The EEPROM versions of the power units do not match.
Fault value (r0949, interpret decimal):
Parameter in which the first different version number was detected.

Remedy:

Use power units with the same EEPROM version.
Note:
For parallel circuit configurations, only power units with identical EEPROM versions may be used.

F05057

Parallel circuit: Power unit firmware versions differ

Message value:

Parameter: %1

Drive object:

All objects

Reaction:

OFF2 (NONE)

Acknowledge:

IMMEDIATELY

Cause:

The firmware versions of the power units connected in parallel do not match.
Fault value (r0949, interpret decimal):
Parameter in which the first different version number was detected.

Remedy:

Use power units with the same firmware version.
For parallel circuit configurations, only power units with identical firmware versions may be used.

F05058

Parallel circuit: VSM EEPROM versions differ

Message value:

Parameter: %1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

The EEPROM versions of the Voltage Sensing Modules (VSM) do not match.
Fault value (r0949, interpret decimal):
Parameter in which the first different version number was detected.

Remedy:

For parallel circuit configurations, only Voltage Sensing Modules (VSM) with identical EEPROM versions may be used.

F05059

Parallel circuit: VSM firmware versions differ

Message value:

Parameter: %1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

The firmware versions of the Voltage Sensing Module (VSM) do not match.
Fault value (r0949, interpret decimal):
Parameter in which the first different version number was detected.

Remedy:

For parallel circuit configurations, only Voltage Sensing Modules (VSM) with identical firmware versions may be used.

F05060

Parallel circuit: Power unit firmware version does not match

Message value:

Parameter: %1

Drive object:

All objects

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

422

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands