manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 516

Acknowledge:

IMMEDIATELY

Cause:

The following applies for CU31x and CUA31:
More than one setpoint telegram was not able to be transferred to the power unit module.

Remedy:

The following applies for CU31x and CUA31:
Check the interface (adjustment and locking) to the power unit module.

A30073 (N)

Actual value/setpoint preprocessing no longer synchronous

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

Communication with the power unit module is no longer in synchronism with the current control cycle.

Remedy:

Wait until synchronization is re-established.

Reaction upon N: NONE
Acknowl. upon N: NONE

F30074 (A)

Communication error between the Control Unit and Power Module

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

Communications between the Control Unit (CU) and Power Module (PM) via the interface no longer possible. The CU may 

have been withdrawn or is incorrectly inserted.
Fault value (r0949, interpret hexadecimal):
0 hex:
- a Control Unit with external 24 V supply was withdrawn from the Power Module during operation.
- with the Power Module switched off, the external 24 V supply for the Control Unit was interrupted for some time.
1 hex:
The Control Unit was withdrawn from the Power Module during operation, although the encoderless safe motion monitoring 

functions are enabled. This is not supported. After re-inserting the Control Unit in operation, communications to the Power 

Module no longer possible.
20A hex:
The Control Unit was inserted on a Power Module, which has another code number.
20B hex:
The Control Unit was inserted on a Power Module, which although it has the same code number, has a different serial 

number.
601 hex:
The Control Unit was inserted on a Power Module, whose power/performance class (chassis unit) is not supported.

Remedy:

Reinsert the Control Unit (CU) or the Control Unit Adapter (CUAxx) onto the original Power Module and continue operation. 

If required, carry out a POWER ON for the CU and/or the CUA.

Reaction upon A: NONE
Acknowl. upon A: NONE

F30080

Power unit: Current increasing too quickly

Message value:

Fault cause: %1 bin

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

514

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands