manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 269

Note
SOS: Safe Operating Stop

p9531[0...3]

SI Motion SLS limit values

 

Changeable: C2(95)

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.00 [mm/min]

Max: 1000000.00 [mm/min]

Def: 2000.00 [mm/min] 

Description:

Sets the limit values for the function "SLS" function.

Index:

[0] = Limit value SLS1
[1] = Limit value SLS2
[2] = Limit value SLS3
[3] = Limit value SLS4

Dependency:

See also:  p9563
See also:  C01714

Note
SLS: Safely Limited Speed

p9533

SI Motion SLS setpoint speed limiting

 

Changeable: T, U

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.000 [%]

Max: 100.000 [%]

Def: 80.000 [%] 

Description:

This is an evaluation factor to define the setpoint limit from the selected actual speed limit.
The active SLS limit value is evaluated with this factor and is made available as setpoint limit in r9733.

Dependency:

This parameter only has to be parameterized for the motion monitoring functions integrated in the drive (p9601.2 = 1)
r9733[0] = p9531[x] x p9533 (converted from the load side to the motor side)
r9733[1] = - p9531[x] x p9533 (converted from the load side to the motor side)
[x] = Selected SLS stage
Conversion factor from the motor side to the load side:
- motor type = rotary and axis type = linear: p9522 / (p9521 x p9520)
- otherwise: p9522 / p9521
See also:  p9501, p9531, p9601

Note
The active actual speed limit is selected via safety-relevant inputs.
When selecting SOS or a STOP A ... D, setpoint 0 is specified in r9733.
SLS: Safely Limited Speed

p9539[0...7]

SI Motion gearbox direction of rotation reversal

 

Changeable: C2(95)

Data type: Integer16

P group: Safety Integrated

Min: 0

Max: 1

Def: 0 

Description:

Sets the direction of rotation reversal for the gearbox.
0: No direction of rotation reversal
1: Direction of rotation reversal

Index:

[0] = Gearbox 1
[1...7] = Reserved

Dependency:

See also:  p9521

p9542

SI Motion actual value comparison tolerance (cross-check)

 

Changeable: C2(95)

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.0010 [mm]

Max: 360.0000 [mm]

Def: 0.1000 [mm] 

Description:

Sets the tolerance for the data cross-check of the actual position between the two monitoring channels.

Dependency:

See also:  C01711

Parameters

12.2 List of parameters

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

267

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands