manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 38

3.1.2

Cables

Cables with a high level of interference and cables with a low level of interference are 

connected to the converter.

Note
Cables with a high level of interference must be shielded.

● Cables with a high level of interference:

– Cable between the line filter and converter
– Motor cable
– Cable between the converter and external braking resistor

● Cables with a low level of interference:

– Cable between the line and line filter
– Signal and data cables

Cable routing inside the cabinet

● Route the cables with a high level of interference so that there is the largest possible 

clearance to cables with a low level of interference.

● Cables with a high level of interference and cables with a low level of interference may only 

cross over at right angles:

● Keep all of the cables as short as possible.
● Route all of the cables close to the mounting plates or cabinet frames. 
● Route signal and data cables - as well as the associated equipotential bonding cables - 

parallel and close to one another.

● Twist incoming and outgoing unshielded individual conductors.

Alternatively, you can route incoming and outgoing conductors in parallel, but close to one 

another.

● Ground any unused conductors of signal and data cables at both ends.
● Signal and data cables must only enter the cabinet from one side, e.g. from below.
● Use shielded cables for the following connections:

– Cable between the converter and line filter
– Cable between the converter and motor
– Cable between the converter and external braking resistor

Configuring
3.1 EMC-compliant installation of a machine or system

SINAMICS S210 servo drive system

36

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands