manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 480

Acknowledge:

NONE

Cause:

The angular commutation offset (p0431) was re-defined and has still not been saved.
In order to permanently accept the new value, it must be saved in a non-volatile fashion (p0971, p0977).

Remedy:

Not necessary.
This alarm is automatically withdrawn after the data has been saved.
See also: p0977

Reaction upon N: NONE
Acknowl. upon N: NONE

F07966

Drive: Check the commutation angle

Message value:

-

Drive object:

All objects

Reaction:

OFF2 (NONE)

Acknowledge:

IMMEDIATELY

Cause:

The speed actual value was inverted and the associated angular commutation offset is not equal to zero and is therefore 

possibly incorrect.

Remedy:

Angular commutation offset after the actual value inversion or determine it again (p1990=1).

A07971 (N)

Drive: Angular commutation offset determination activated

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The automatic determination of the angular commutation offset (encoder adjustment) is activated (p1990 = 1).
Note:
The automatic determination is carried out at the next switch-on command.
For SERVO and fault F07414 present, the following applies:
The determination of the angular commutation offset is automatically activated (p1990 = 1), if a pole position identification 

technique is set in p1980.

Remedy:

Not necessary.
The alarm is automatically withdrawn after successful determination or for the setting p1990 = 0.

Reaction upon N: NONE
Acknowl. upon N: NONE

A07979 (F, N) Drive: pole position identification calibration required

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The pole position identification was not successful as the calibration values for the current measurement are not correct.

Remedy:

Replace the Motor Module involved.

Reaction upon F: OFF2 (NONE)
Acknowl. upon F: IMMEDIATELY
Reaction upon N: NONE
Acknowl. upon N: NONE

A07980

Drive: Rotating measurement activated

Message value:

-

Drive object:

All objects

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

478

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands