Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 295

Page: 295 / 768

Acknowledge:

IMMEDIATELY

Cause:

An internal software error has occurred.
Fault value (r0949, interpret hexadecimal):
Only for internal Siemens troubleshooting.

Remedy:

- carry out a POWER ON (switch-off/switch-on) for all components.
- upgrade firmware to later version.
- contact Technical Support.

F01003

Acknowledgment delay when accessing the memory

Message value:

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY

Cause:

A memory area was accessed that does not return a "READY".
Fault value (r0949, interpret hexadecimal):
Only for internal Siemens troubleshooting.

Remedy:

- carry out a POWER ON (switch-off/switch-on) for all components.
- contact Technical Support.

N01004 (F, A) Internal software error

Message value:

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

An internal software error has occurred.
Fault value (r0949, hexadecimal):
Only for internal Siemens troubleshooting.

Remedy:

- read out diagnostics parameter (r9999).
- contact Technical Support.

Reaction upon F: OFF2
Acknowl. upon F: POWER ON
Reaction upon A: NONE
Acknowl. upon A: NONE

F01005

Firmware download for DRIVE-CLiQ component unsuccessful

Message value:

Component number: %1, fault cause: %2

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

293

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands