manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 529

Remedy:

- check whether there are faults in the safety function alignment between the two monitoring channels (F01655, F30655) 

and if required, carry out diagnostics for the faults involved.
- use a Control Unit that supports the safe motion monitoring function.
- upgrade the Control Unit software.
Note:
SI: Safety Integrated

F30674

SI Motion P2: Safety function not supported by PROFIsafe telegram

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

The monitoring function enabled in p9501 and p9601 is not supported by the currently set PROFIsafe telegram (p9611).
Note:
This fault does not result in a safety stop response.
Fault value (r0949, interpret bitwise binary):
Bit 18 = 1:
SS2E via PROFIsafe is not supported (p9501.18).
Bit 24 = 1:
Transfer SLS limit value via PROFIsafe not supported (p9501.24).

Remedy:

- Deselect the monitoring function involved (p9501, p9601).
- set the matching PROFIsafe telegram (p9611).
- using the commissioning tool, copy the safety parameters and confirm the data change.
Note:
SI: Safety Integrated
SLS: Safely Limited Speed
SS2E: Safe Stop 2 external (Safe Stop 2 with external stop, external STOP D)

F30680

SI Motion P2: Checksum error safety monitoring functions

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The actual checksum over the safety-relevant parameters calculated by monitoring channel 2 does not match the reference 

checksum saved at the last machine acceptance.
Safety-relevant parameters have been changed or a fault is present.
Note:
This fault results in a STOP A that can be acknowledged.
Fault value (r0949, decimal interpretation):
0: Checksum error for SI parameters for motion monitoring.
1: Checksum error for SI parameters for component assignment.

Remedy:

- check the safety-relevant parameters and if required, correct.
- execute the function "Copy RAM to ROM".
- perform a POWER ON if safety parameters requiring a POWER ON have been modified.
- carry out an acceptance test.

F30681

SI Motion P1: Incorrect parameter value

Message value:

Parameter: %1, supplementary information: %2

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

527

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands