manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 64

Sequence diagram

212))

2SHQPRWRUKROGLQJEUDNH

$FW

LR

Q

0R

WR

U

UH

VS

RQ

VH

&

RQ

YH

UWH

UUH

VS

RQ

VH

0RWRUKROGLQJEUDNHRSHQ

672GHVHOHFWLRQ

6SHHG

672DFWLYH

6%&UHTXHVWHG

5HDG\IRUVZLWFKLQJ

0RWRUEUDNHVWR

VWDQGVWLOO

7LPHIRUEUDNHRSHQLQJRSHUDWLRQ

7LPHIRUEUDNHFORVLQJRSHUDWLRQ

W

W

W

0

0

0

STO is selected during operation via the control bit of the selected PROFIsafe telegram or via the 
F-DI.
Safe Brake Control (SBC) is activated at the same time. Taking the brake closing time (r1217) 
into account, the command to close the motor holding brake closes the brake, thus supporting the 
shutdown process initiated by STO.

The mechanical brake brakes the motor down to standstill.

The converter goes into the "Ready to start" state, when STO is deselected via PROFIsafe or F-
DI. SBC is reset at the same time. The brake remains (unsafely) closed until the standard program 
executes the command to open the brake.

The converter switches the motor on again with a positive signal edge at ON/OFF.
Taking the brake opening time (r1216) into account, the command to open the motor holding brake 
opens the brake.

The converter carries out a check to ensure that the "Safe Brake Control" function is working 

properly and ensures that - if there is a failure or fault - the brake current is interrupted and the 

brake is thus applied. 

　

 If a fault is detected by the converter, the brake current is 

disconnected. The brake then closes and a safe state is reached.

Safety functions integrated in the drive
4.2 Basic Functions

SINAMICS S210 servo drive system

62

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands