manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 176

7.5

Faults

Faults

Faults have the following properties:
● The fault causes the motor to be switched off.
● Faults must be acknowledged.
● Faults are displayed as follows:

– In the PLC according to the PROFIdrive message class
– On the drive via LEDs
– At the drive using the three-digit display according to the PROFIdrive message classes
– In the Web server via the "Diagnostics - Messages" view

Acknowledge fault

Before you can acknowledge a fault, you must have resolved the cause of the fault.
To acknowledge, you have the following options:
● Acknowledging via the PLC
● Acknowledging via the OK button under the front cover
● Switch off the converter power supply and switch on again
● Acknowledging via the Web server
Faults detected during the converter-internal monitoring of hardware and firmware can be 

acknowledged only by switching the power supply off and on again. In the list of faults, you 

will find the information on limitations when acknowledging at the corresponding fault codes.

Reference

You can find additional information on faults in Chapter "Overview of faults and alarms 

(Page 291)".

Diagnostics
7.5 Faults

SINAMICS S210 servo drive system

174

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands