manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 368

Cause:

Safety parameters have been changed; these will only take effect following a warm restart or POWER ON (see alarm 

A01693).
A partial power up (boot) with modified configuration was then performed.

Remedy:

- carry out a warm restart
- carry out a POWER ON (switch-off/switch-on).

F01680

SI Motion P1 (CU): Checksum error safety monitoring functions

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The actual checksum over the safety-relevant parameters, calculated and entered by the drive, does not match the 

reference checksum last saved for the last machine acceptance.
Safety-relevant parameters have been changed or a fault is present.
Note:
This fault results in a STOP A that can be acknowledged.
Fault value (r0949, decimal interpretation):
0: Checksum error for SI parameters for motion monitoring.
1: Checksum error for SI parameters for actual values.
2: Checksum error for SI parameters for component assignment.

Remedy:

- check the safety-relevant parameters and if required, correct.
- execute the function "Copy RAM to ROM".
- perform a POWER ON if safety parameters requiring a POWER ON have been modified.
- carry out an acceptance test.

F01681

SI Motion P1 (CU): Incorrect parameter value

Message value:

Parameter: %1, supplementary information: %2

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

366

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands