manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 274

Note
In an extended sense, bus failure is interpreted here as a communication fault in the control signals of the safety 

functions (e.g. via PROFIsafe).
SDI: Safe Direction (safe motion direction)

p9568

SI Motion SAM/SBR speed limit

 

Changeable: C2(95)

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.00 [mm/min]

Max: 1000.00 [mm/min]

Def: 0.00 [mm/min] 

Description:

Sets the velocity limit for the "SAM" and "SBR" functions.
If the drive is being ramped down, but accelerates by the tolerance in p9548, then the SAM function identifies this and 

a STOP A is initiated.
The monitoring operates as follows:
- monitoring by SAM is activated for SS1 (or STOP B) and SS2 (or STOP C).
- the SAM limit value is frozen after the velocity limit in p9568 is undershot.
- SAM monitoring is still executed until the transition time to SOS/STO has expired.

Note
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
SBR: Safe Brake Ramp (safe brake ramp monitoring)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the speed monitoring)
For p9568 = 0, the following applies:
The value in p9546 (SSM) is applied as the velocity limit for SAM/SBR.

p9570

SI Motion acceptance test mode

 

Changeable: T, U

Data type: Integer16

P group: Safety Integrated

Min: 0000 hex

Max: 00AC hex

Def: 0000 hex 

Description:

Setting to select and de-select the acceptance test mode.

Value:

0:

[00 hex] De-select the acceptance test mode

 

172:

[AC hex] Select the acceptance test mode

Dependency:

See also:  p9558, r9571, p9601
See also:  C01799

Note
Acceptance test mode can only be selected if the safe motion monitoring functions are enabled.

r9571

SI Motion acceptance test status

 

Data type: Integer16

P group: Safety Integrated

 

Description:

Displays the status of the acceptance test mode.

Value:

0:

[00 hex] Acc_mode inactive

 

12:

[0C hex] Acc_mode not possible due to POWER ON fault

 

13:

[0D hex] Acc_mode not possible due to incorrect ID in p9570

 

15:

[0F hex] Acc_mode not possible due to expired Acc_timer

 

172:

[AC hex] Acc_mode active

Dependency:

See also:  p9558, p9570
See also:  C01799

p9580

SI Motion stop response delay bus failure

 

Changeable: C2(95)

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.00 [ms]

Max: 800.00 [ms]

Def: 0.00 [ms] 

Description:

Sets the delay time, after which the stop response parameterized in p9612 for bus failure is executed.

Dependency:

See also:  p9563

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

272

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands