manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share
Download
Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 453

F07515

Drive: Power unit and motor incorrectly connected

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY

Cause:

A power unit (via PDS) was assigned to a motor (via MDS) in a drive data set that is not connected in the target topology. 

It is possible that a motor has not been assigned to the power unit (p0131).
Fault value (r0949, interpret decimal):
Number of the incorrectly parameterized drive data set.

Remedy:

- assign the drive data set to a combination of motor and power unit permitted by the target topology.
- adapt the target topology.
- if required, for a missing motor, recreate the component (drive Wizard).

F07516

Drive: Re-commission the data set

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

The assignment between the drive data set and motor data set (p0186) or between the drive data set and the encoder 

data set was modified (p0187). This is the reason that the drive data set must re-commissioned.
Fault value (r0949, interpret decimal):
Drive data set to be re-commissioned.

Remedy:

Commission the drive data set specified in the fault value (r0949).

F07517

Drive: Encoder data set changeover incorrectly parameterized

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY

Cause:

In at least two drive data sets (DDS), the same motor data set (MDS) is assigned different encoder data sets (EDS) for 

the motor encoder. In various DDSs, it is not permissible for an MDS to have different motor encoders.
The following parameterization therefore results results in an error:
DDS0: p0186[0] = 0, p0187[0] = 0
DDS1: p0186[1] = 0, p0187[1] = 1
Fault value (r0949, interpret decimal):
The lower 16 bits indicate the first DDS. The upper 16 bits indicate the second DDS.

Remedy:

Create two MDS with the same motor data in order to operate one motor with different motor encoders.
Example:
DDS0: p0186[0] = 0, p0187[0] = 0
DDS1: p0186[1] = 1, p0187[1] = 1

F07518

Drive: Motor data set changeover incorrectly parameterized

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

451

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands