Octel XC1000, Service Manual

Page: 218 / 889

TROUBLESHOOTING
6-19 Edition One XC1000 Service
LOAD SST: OK
CARD CONFIGURATION: FMm––A–L–L–L–L–L–L––––––––––––––––––
DATA BUS DMA: OK
LINE CONFIGURATION: 72
LINE: 1A 1B 1C 1D 1E 1F 1G 1H 1I 1J 1K 1L 2A 2B 2C 2D 2E 2F 2G 2H 2I 2J 2K 2L
HARD: 08 08 08 08 08 08 08 08 08 08 08 08 10 10 10 10 10 10 10 10 10 10 10 10
SOFT: 00 01 02 03 04 05 06 07 08 09 0A 0B 00 01 02 03 04 05 06 07 08 09 0A 0B
TIC: 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05
LINE: 3A 3B 3C 3D 3E 3F 3G 3H 3I 3J 3K 3L 4A 4B 4C 4D 4E 4F 4G 4H 4I 4J 4K 4L
HARD: 12 12 12 12 12 12 12 12 12 12 12 12 14 14 14 14 14 14 14 14 14 14 14 14
SOFT: 00 01 02 03 04 05 06 07 08 09 0A 0B 00 01 02 03 04 05 06 07 08 09 0A 0B
TIC: 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05
LINE: 5A 5B 5C 5D 5E 5F 5G 5H 5I 5J 5K 5L 6A 6B 6C 6D 6E 6F 6G 6H 6I 6J 6K 6L
HARD: 16 16 16 16 16 16 16 16 16 16 16 16 18 18 18 18 18 18 18 18 18 18 18 18
SOFT: 00 01 02 03 04 05 06 07 08 09 0A 0B 00 01 02 03 04 05 06 07 08 09 0A 0B
TIC: 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05
[ Second TIC screen follows.]
TOTAL OF 72 LINES FOUND
PRESS ANY KEY TO PAUSE
LOAD APPLICATION: OK
APPLICATION SUCCESSFULLY LOADED
Starting up System Services Partition
Checking Data Directory...
Loading Address Management Table...
Figure 6-10. Example of the IPL3 Screen Showing
Line Configurations for a Single-Cabinet XC1000.
6.2.6.1 SST Loading. In the rare case where the SST does not load correctly,
immediately call the Octel Communications Technical Assistance Center.
6.2.6.2 Card-Configuration Test. The CPU sends a broadcast control-bus
message to all cards in the XC1000, directing them to identify themselves.
The card configuration is displayed after the file card and DLCs respond to
the CPU message. Figure 6-10 shows the card configuration on the IPL3
screen, in the
CARD CONFIGURATION: field.
The card configuration displayed represents the physical location of the
cards in the XC1000 cabinet. The CPU does not report its own location in
the card configuration. Only the monitor card, file cards, and DLC loca-
tions are displayed. TICs are not represented in the card configuration
because they are not connected to the data or control buses.
The following abbreviations are displayed to represent each card:
F System file card
M
Message file card
m Monitor card
– CPU, TIC, or empty slot
L DLC
A ACP
SECTION 6.2