![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657082.webp)
GBC StreamWire
07/23/2020
RTPS
2-67
7. Check the area exposed in step 1 for debris i.e. screws, elements, or
other foreign objects
Closer cam and chain areas are free of foreign objects.
Yes
- Go to Step 7.
No
- Remove the object(s). If the debris is unable to be removed, do
REP 6.4 to remove the M20 Closer Motor. Rotate the large
drive gear by hand to rotate the cams and chain and release
any objects. If the debris is still unable to be removed, escalate
to second level.
This clears the fault
Yes
- Reinstall the covers and return to normal operation;
No
- Go to Step 8.
8. Do GP 6.5 to check M20 Closer Motor.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 9.
9. Do GP 6.3.3 Motors Procedure to turn on M20 Closer Motor. Check if
the rear cam is turning.
The rear cam is turning
Yes
- Go to Step 10;
No
- Check if the M5 Screw in the collar on the rear shaft is properly
tight. The screw should be tightened to a torque of 8 Nm.
The screw is properly tightened
Yes
- Escalate to second level;
No
- Tighten the screw to 8 Nm.
This clears the fault
Yes
- Follow the steps in Section 3.1 Element Closing
to achieve proper bind quality then return to
normal operation;
No
- Go to step 10.
10. Do GP 6.4 to check S48 Closer Encoder Sensor.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 11.
11. Check that the element size that this jam occurred with is loaded. Do
GP 6.3.13 to record the current Partial Close value and then
decrease it by 5. Continue running books and decreasing this value
until this jam no longer occurs during a job.
This clears the fault
Yes
- Follow the steps in Section 3 - Book Quality to regain quality
binds and return to normal operation. Repeat this step if this jam
was encountered on any other size elements;
No
- Reset the Partial Close setting to its initial value and go to Step
12.
12. Do GP 6.3.5 FIRMWARE UPGRADE Procedure to Re-flash the
firmware for eWire.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 13
13. Do REP 11.2 “B” Main Control Board Replacement
.
This clears the fault
Yes
- Return to normal operation;
No
- Escalate to second level
Summary of Contents for StreamWire
