Repairs/Adjustments
07/23/2020
GBC StreamWire
4-204
ADJ 1.20 Cover Interlock Flag Adjustment
This adjustment will set the spring loaded interlock flag at the correct
location and ensure the machine operates correctly while the cover is
closed and opens once the cover latch is disengaged.
Adjustment Procedure
1) Follow REP 1.1 to remove the top cover.
2) Carefully close and latch the Upper Paper Transport.
3) Loosen but do not remove the M4 fasteners (2) securing the Interlock
Flag Assembly
4) Gently push down on the interlock flag assembly until the spring
loaded flag contacts the sides of the interlock. Reference the scribe
line on the flag for correct interlock setting. Example can be seen
below.
5) Tighten the M4 fasteners (2) securing the Interlock Flag Assembly.
6) Follow REP 1.1 to reinstall the top cover.
7) Test the interlock is functioning properly. Close cover and the
machine should show “Ready” or “Bypass”. Press latch release and
the cover should lift slightly. Ensure display shows “Close Cover”
when the cover lifts slightly.
ADJ 1.21 Element Shield Adjustment
If the element shield requires adjustment it can bend down towards the
ground and contact the supply spool. This will increase the force require
to turn the rewind spool and result in repeated paper tears and J320
Spool Element Slack Timeouts
Inspection Procedure
1) Remove the element feeder shield and check that the 2 studs on the
shield are tight. If they are loose, tighten the button head cap screws
using a 2.5mm hex key and an 8mm crescent wrench to prevent the
studs from rotating.
2) Mount the element feeder shield with a spool loaded on the spindle,
making sure that the pins are fully seated in the hole and slot, and
that the side of the shield is in contact with the magnet.
Summary of Contents for StreamWire
