![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657051.webp)
GBC StreamWire
07/23/2020
RTPS
2-36
RTP 4.11
J351- S32 & S33 BOTH BLOCKED
J351 will occur when the S32 and S33 sensors are both blocked at the
same time. S32 and S33 sensors are both used on the Pushover
mechanism.
1. Open the Element Feeder drawer. Inspect the pushover mechanism
area for any debris or obstruction. Inspect the 4 Cams for damage.
Remove any foreign object that may be obstructing the area.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 2
2. Do GP 6.4.3 to check the S32 and S33 sensors.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 3
3. Do GP 6.5.7 to check the function of Motor 12 and Motor 13.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 4
4. Do REP 3.15 to remove the Expanding T mechanism from the eWire.
Thoroughly inspect and ensure no foreign objects are stuck in the
Expanding T. Replace the module and repeat steps 2 and 3.
This clears the fault
Yes
- Return to normal operation;
No
- Escalate to second level.
RTP 4.12 J361- RESIDUAL ELEMENT ERROR
J361 is displayed when there is a residual element on the Element Feed
Belt somewhere between S21 Element detect at Knife and S22 Element
detect at Pyramid. Follow this procedure when this message is displayed
erroneously (i.e. when there is no element present on the belt) or if this
jam occurs very frequently during operation.
1. Check the Element Feed Belt area for dust and debris. Use
compressed air to clean the areas around S21 and S22. Do GP
6.15.5 to clean the film between the S22 sensor emitter and receiver.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 2
2. Do GP 6.4 to check the S21, S22 & S25 sensors.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 3
3. Check that all Interlocks are being properly engaged. An improperly
set flag or defective interlock may cut power to the machine
unexpectedly during a feed element operation.
A message CLOSE DOOR, CLOSE TRAY, or CLOSE COVER
displays briefly during operation before showing J361
Yes
- Do ADJ 1.7 to adjust the Interlock Flags;
No
- Go to Step 4
4. Inspect the Element Feed Belt for damage. Observe each tooth to
ensure there are no large cracks or gouges.
Element Feed Belt is damaged
Yes
- Do REP 3.6 to replace the Element Feed Belt;
No
- Go to Step 5
5. Do ADJ 1.17 to check the Element Feed Belt tension.
Element Feed Belt is properly tensioned.
Yes
- Escalate to second level;
No
- Do ADJ 1.17 to correct the Element Feed Belt tension.
Summary of Contents for StreamWire
