GBC StreamWire
7/23/2020
Repairs/Adjustments
4-189
NOTE: When changing the DESKEW ADJUST and ALIGNMENT
settings these values correspond to all element sizes. When
changing the DEFLECTOR setting this value only corresponds to
the currently loaded element size.
12) Check and correct the sheet skew. Do GP 6.1.3 to access the
DESKEW ADJUST setting.
If the small hole on the right is too close to the edge and the small
hole on the left is too far away decrease this value by 1.
If the small hole on the right is too far away from the edge and the
small hole on the left is too close increase this value by 1.
Repeat step 5-6 and 12 until the holes are the same distance from
the trail edge, they do not need to be the correct distance.
Both small holes are the same distance from the edge of the
sheet
Yes-
Go to Step 13
No-
Repeat this step
13) Check and correct the deflector timing and alignment. Do GP 6.1.2 to
access the DEFLECTOR setting and the ALIGNMENT setting.
A compass is provided on the Punched Hole Position Check Tool
to assist in determining the direction of the needed adjustment. The
arrow pointing in the direction the small hole needs to move in order
to be in its optimal position has a + or a – next to it and either the
word DEFLECTOR or ALIGNMENT. + means the value should be
increased in mm. – means the value should be decreased in mm.
Make a small adjustment to the appropriate setting then repeat
Step 5-6 and 13.
The small holes are in their optimal positions
Yes-
Go to Step 14
No-
Repeat this step
14) Remove the die from the punch, reinsert the pins and reinstall the die.
Run books to verify the issue is corrected.
Issue is corrected
Yes
- Return to normal operation
No
- Return to the trouble shooting step that directed you here.
Summary of Contents for StreamWire
