![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657379.webp)
General Procedures and Information
07/23/2020
GBC StreamWire
6-42
9. Check that the cable(s) connecting the Driver Board Control signal to
the Main Control Board are intact. Refer to the motor cables table to
identify the appropriate cable part numbers,
The cables look okay
Yes
- Go to Step 10
No
- Replace the faulty cable and repeat Step 1
firmware for the eWire
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 11
11. Replace the driver board for the faulty motor, with DIP switch set
correctly for the position you are replacing. Refer to REP 2.17 for
Motors M1, M2, and M4. Refer to REP 2.24 for Motors M16, M17, and
M18.
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 12
12. Replace the faulty stepper motor
REP 2.10 for M1 & M2
REP 2.22 for M16 and M17
REP 2.23 for M18
REP 2.28 for M4
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 13
13. Replace Main Control Board A (REP 11.1)
This clears the fault
Yes
- Resume normal operation
No
- Escalate to second level
GP 6.5.2
Check M3 & M5
Locate Motors M3 and M5:
•
Raise the top cover and lower bypass
•
M3 is located on the deflector module. You should be able to
hear the motor run and see the deflector rollers rotate when
motor is activated.
•
M5 is located on the vacuum stacker module. Refer to PL 5.14.
The green belts will turn when M5 is activated.
•
Insert a cheater into the upper bypass panel interlock switch
1. Do
to check that the corresponding
motors turn. M3 turns the N8 nip rollers. M5 turns the green belts on
the vacuum stacker.
The corresponding components turn when the Motor is activated
Yes
- Return to the RTP that directed you here
No
- Identify the malfunctioning Motor(s) and go to Step 2.
2. Make sure the motor wire is connected securely at the Driver Board
and at the Main Control Board (PL 5.27). Do REP 1.5 to remove the
Rear Cover to gain access to the Main Control Board. For Motor M3,
the Driver Board is located on the rear of the eWire. For Motor M5, do
REP 1.6 to remove the Side Cover. The Motor Driver for M5 is
located on the left side of the eWire frame.
All the connectors are securely connected.
Yes
- Go to Step 3
No
- Make the connection and resume operation
3. Inspect the timing belt for the corresponding motor drive. Ensure that
the timing belt is not broken or frayed. Refer to the sections below to
access the appropriate timing belt Path Motor Replacement
•
M5: Refer to REP 4.9, Stacker Drive Belt Replacement
Timing Belt Looks OK
Yes
- Go to Step 4
No
- Replace the faulty belt and resume operation
Summary of Contents for StreamWire
