GBC StreamWire
07/23/2020
General Procedures and Information
6-35
Locate Sensor S42:
•
Slide the book drawer tray all the way out of the eWire.
•
Block the sensor path by covering the sensor beam path
holes at the upper portion of the book drawer.
•
S42 has 2 emitters and 2 receivers, both must be blocked to
check the sensor.
S42 is located in the book drawer
Check Sensors Procedure (S21, S22, S25, S42)
1. Do
SENSORS Procedure
. Check to make sure S21, S22,
and S25change state from “1” to “0” when blocked. S42 will change from
“0” to “1”
If any sensor shows “0” when uncovered, clean that sensor. Also
check if there is any obstruction in the sensor window. Use
compressed air to clear dust from sensor area.
All sensors operate correctly
Yes
- Go to Step 2
No
- Go to Step 3
2. Test the open voltage reading of the sensor. To do this, ensure that
the path between the sensors is clear, and place one lead of a multi-
meter on the test point with the appropriate sensor label on the AC
board, and the other lead on the ground test point.
Voltage reading is less than 0.4V
Yes
- Go to Step 3
No
- Go to Step 4
3. Make sure the sensor wire is connected securely at the Sensor and at
the Main Control Board (PL 5.27). Do REP 1.5 to remove the Rear
Cover to gain access to the connector at the Control Board. Refer to
to locate the termination location for each sensor. For S22
see details at the end of this section.
All the connections are made securely
Yes
- Go to Step 4
No
- Make the connection and return to normal operation.
4. Replace the faulty sensor board.
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 5
5. Visually inspect the Cable from the sensor all the way to the Control
Board (PL 5.27). If the Cable is damaged, replace the Cable. See
for cable part numbers and locations.
Sensor cable looks okay
Yes
- Go to Step 6
No
-
Go to Step 7
6. Do
FIRMWARE UPGRADE Procedure to Re-flash the
firmware for the eWire.
This clears the fault
Summary of Contents for StreamWire
