![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657294.webp)
GBC StreamWire
7/23/2020
Repairs/Adjustments
4-197
ADJ 1.15 Element Feeder Horizontal Position Adjustment
The Element Feeder horizontal position is controlled by a pin and plate at
the back on top of the drawer. Set this to ensure the holder pins are
aligned with the element feeder location holes.
Inspection Procedure
1) Close the top cover or use an interlock cheat to home the machine.
2) Access the Service Menu and select Holder to Xfer.
Service Menu
Function Tests
Holder to Xfer
3) Open the top cover or remove the interlock cheat and manually pull
the holder out from the feeder so that the pins are close to but not
engaged with the element feeder holes.
4) Manually push the holder forward so that the pins slowly engage with
the element feeder holes and watch for any horizontal shift. Repeat a
few times in case needed to observe any shift.
5) If there is noticeable shift proceed to adjustment.
Adjustment Procedure
1) Ensure the holder is back in its home position.
2) Open the element feeder drawer so that the pin bracket is exposed,
next to the stacking tray, and loosen the 2 screws that hold the pin
plate to the feeder drawer.
3) Remove the rear cover per REP 1.5.
4) Loosen the 2 screws on the latch bracket at the back of the drawer
and pull it to the back of the machine.
5) Slide the element feeder drawer in. As the plate and the latch bracket
are loose it will not stop in a firm location. Ensure the holder is in the
home position before sliding the drawer in.
6) Manually push the holder forward so that the pins are close to but not
engaged with the element feeder holes.
7) Align the element feeder drawer so the holder can be pushed forward
and the pins engage in the feeder holes.
8) Move the holder in and out of the feeder just enough to check that the
holder pins do not shift when being inserted in the feeder holes.
Adjust the horizontal position of the feeder by hand until the holder
pins do not shift to engage the holes.
9) Once there is no noticeable shift, when the holder is pushed forward,
leave the pins engaged in the feeder.
Summary of Contents for StreamWire
