![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657387.webp)
General Procedures and Information
07/23/2020
GBC StreamWire
6-50
GP 6.5.8
Check M15 and M21
WARNING
Moving Parts, keep hands clear of the eWire when
performing motor checks. Make sure that power is
disconnected from the machine before touching any
moving parts.
Locate Motor M15 and M21:
•
Open the lid and raise the lower bypass panel.
•
M15 drives the linear travel belt for the Holder Module. M21
drives the linear travel belt for the Closer Module.
1. To check the motor function, manually move the Closer Module and
Holder Module forward. When an interlock cheater is inserted, the
Closer and Holder will return to their home positions (at the far right of
the eWire).
Motors return to home position as expected
Yes
- Return to the RTP that directed you here
No
- Go to Step 2.
2. Make sure the motor wire is connected securely at the Driver Board
and at the Main Control Board (PL 5.27). Do REP 1.5 to remove the
Rear Cover to gain access to the connector at the Control Board. The
motor Driver boards are located on the rear of the eWire Frame.
All the connectors are securely connected.
Yes
- Go to Step 3
No
- Make the connection and resume operation
3. Inspect the timing belt. Confirm that the belt is not frayed or worn and
that no teeth are missing.
Belt looks OK
Yes
- Go to Step 4
No
- Follow REP 8.10 to replace Closer Linear Belt or 8.11 and 8.12
to replace Holder Linear Belt.
4. Check the tightness of the set screw of the pulley on the stepper
motor shaft.
All the set screws are secured tightly
Yes
- Go to Step 5
No
- Tighten the loose set screw and repeat Step 1
5. Check the DIP switch settings for the Driver Board. Refer to the table
below.
DIP 1
DIP 2
DIP 3
DIP 4
DIP 5
M15
OFF
OFF
ON
OFF
OFF
M21
OFF
OFF
ON
OFF
OFF
DIP switch setting are correct
Yes
- Go to Step 6
No
- Correct the DIP switch and repeat Step 1
6. Check if there is power to the Driver board. LED 1 on the Driver board
should be lit.
If LED 1 is lit, it means there is 24V DC power to the Driver board
from the Main Control board.
If LED 2 is lit, it means there is a fault with either the Driver board or
the stepper motor.
Continue to Step 7
7. Check that the cable(s) connecting the Driver Board to the Main
Control Board are intact. Refer to the motor cables table to identify
the appropriate cable part numbers,
The cables look okay
Yes
- Go to Step 8
No
- Replace the faulty cable and resume normal operation
firmware for the eWire
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 9
Summary of Contents for StreamWire
