Repairs/Adjustments
07/23/2020
GBC StreamWire
4-178
Adjustments
ADJ 1.1 Element Position Skew Adjustment
Inspection Procedure
1) Locate the Element Height Setup Tool, which is attached to the
eWire Book Tray Door.
2) Pull out the Element Feeder tray, and insert a cheat into the
interlock for the Element Feeder Door.
3) Enter the Service Menu, and select
Function Tests
Pushover
Out.
This will move the Expanding T to its forward position.
4) Using the Setup Tool, press the front flat surface of the tool
against the Element Feeder face. The notch on the Setup Tool is
set to 16 mm, which is the correct position of the Expanding T Out.
1) Repeat the process on the front and rear of the machine. If the
Expanding T front face is not touching the tool or the tool is not
touching the blue feeder track face, refer to the adjustment steps
below. If both of the tool faces are touching the expanding T and
blue feeder track, return to the procedure that directed you here.
Adjustment Procedure
1) Remove the screws and nuts (5 total) from the locations shown
and remove the Covers.
2) Locate the screws indicated in the picture below. Loosen the lock
nuts with a wrench. Turn the screws clockwise to decrease
Expanding T Out. Turn the screws counter-clockwise to increase
Expanding T Out. If the Expanding T Out position is skewed, try
adjusting only one screw to correct it.
3) After adjustment is complete, tighten the lock nuts. Repeat the
Inspection Procedure to determine if the desired location has been
reached.
4) If additional adjustment is needed, repeat steps 2 and 3. If the
position is now correct, return to the procedure that directed you
here.
Summary of Contents for StreamWire
